Deposition and Properties of Superconducting MgB2 Thin Films

The recently discovered superconductor MgB₂ with T _c at 39 K has great potential in superconducting electronics. In this paper, we review the deposition techniques used for MgB₂ thin films in the light of a thermodynamic study of the Mg-B system with the calculation of phase diagrams (CALPHAD) modeling technique. This thermodynamic study identifies a growth window in the pressure–temperature phase diagram, in which the magnesium pressure is very high for likely in situ growth temperatures. A Hybrid Physical–Chemical Vapor Deposition (HPCVD) technique that successfully achieves such a high Mg pressure is shown to produce in situ epitaxial MgB₂ thin films with bulk superconducting properties.     

RF-MBE生长的AlGaN/GaN高电子迁移率晶体管特性

用射频分子束外延技术研制出了室温迁移率为10 35 cm2 /(V·s) ,二维电子气浓度为1.0×10 1 3cm- 2 ,77K迁移率为2 6 5 3cm2 /(V·s) ,二维电子气浓度为9.6×10 1 2 cm- 2 的Al Ga N/Ga N高电子迁移率晶体管材料.用此材料研制的器件(栅长为1μm,栅宽为80μm,源-漏间距为4μm )的室温非本征跨导为186 m S/m m,最大漏极饱和电流密度为92 5 m A/m m,特征频率为18.8GHz.     

杭-宁输气管道工程定向钻穿越设计浅析

杭州-宁波天然气输气管道工程（简称杭-宁输气管道工程）是浙江省天然气长输管网主干线之一，根据工程河流穿越众多、渠塘穿越频繁的特点，对杭-宁输气管道工程水域穿越的特点和穿越方式作了总结；重点分析了水域定向钻穿越设计及需要注意的问题，为今后浙江省天然气管网建设的水域穿越设计作了探讨。     

无线光接入技术

无线光通信系统以其高带宽、低成本和安装迅捷等优势成为非常有竞争力的光接入新技术。对无线光通信系统的关键技术、主要优势和存在的问题及国内外相关产品的发展状况和主要特点进行了论述和介绍。     

基于本地缓存的弹性分组环保护机制

本文提出一种基于本地缓存的弹性分组环保护倒换机制(WrapProtectionBasedOnLocalBuffers,简称WP-LB)。其主要思想是当环路上任何位于源节点和故障区域之间的中间节点接收到含有故障信息的控制信令后,就不再向下游转发数据分组,而是在本地缓存这些数据。等到保护通路建立好之后,再把缓存的数据分组经过保护通路发送给目的节点。分析计算表明,与原有的保护倒换(WrapProtection,简称WP)机制相比,WP-LB机制不仅提高带宽利用率,减少平均时延,并且还能避免数据包的丢失和失序。     

激光二极管线阵光束变换研究

推导出激光二极管线阵光束通过透镜系统的光强分布表达式，分析了出射光束的传输特性，设计一种凹柱透镜的光束变换系统得到一维均匀光强分布。此外，给出扩展角宽度的计算公式。     

聚合反应器制造质量控制要点探讨

聚合反应器是无法检修设备,不允许打开,所以聚合反应器的制造质量必须严格控制,在设备制造过程中,严格按照设计图纸、技术要求及国家现行标准,进行控制设备制造、检验和验收,使制造质量达到规定要求。     

弹性分组环技术

弹性分组环技术是一种新兴的城域网技术。作者主要讨论了弹性分组环技术的特点和优势,并且简要介绍了弹性分组环技术目前在国内城域网建设中的一些应用。弹性分组环技术集以太网的经济性、IP的智能化、光纤环网的丰富带宽和可靠性于一体,是目前宽带IP城域网运营商的最佳组网方案。     

The interfacial microstructure of joined single crystal and polycrystalline alumina

The interfacial microstructures of 96 and 98% polycrystalline alumina joined with single crystal sapphire have been investigated in relation to the joining parameters. Joining has been evaluated based on either using a thin spin-on silica interlayer or by placing the alumina and sapphire in direct contact. The materials were joined by placing the coated or uncoated surfaces in contact and heating in the range of 1340–1475 °C with minimum external load. With the aid of a silica interlayer, sapphire and 98% polycrystalline alumina were successfully joined in 180 min at 1400 °C and above, while samples without a silica interlayer failed to join under these conditions. However, sapphire and 96% polycrystalline alumina were joined both with and without the use of silica interlayer. A variety of interfacial morphologies have been observed, including amorphous regions, fine crystalline alumina, and intimate contact between the sapphire and polycrystalline alumina.     

跳时序列与跳频序列的性能比较

通过对传统通信中跳频序列与超宽带无线电通信中跳时序列的分析比较,得出了两者间相关性能的关系,论述了两者之间的差异,并总结出了将跳频序列转换成为跳时序列的方法,从而为超宽带无线电通信中跳时序列的构造提供了参考。